Ignite supports two rebalancing modes. A mode is selected based on your cluster configuration:
Full rebalancing — this is a default rebalancing mode supported for both pure in-memory clusters and clusters with Ignite Native Persistence. In this mode, a new or restarted node clears all its partitions and transfers data from remote nodes. The node has to empty its partitions only if you use Ignite Native Persistence, and the node was restarted.
Historical rebalancing - this mode is supported for the cluster with Ignite Native Persistence. Consider this mode if nodes leave a cluster for a short time and store large data sets on disk. With historical rebalancing, a partition receives only the delta of updates that happened while the partition’s node was offline.
Historical Rebalancing Requirements
Historical rebalancing relies on the history of updates stored in the write-ahead-log files (WALs) of cluster nodes. The WALs' history must keep updates of all the partitions which deltas need to be rebalanced to a restarted node.
The maximum size of the WALs' archives should be influenced by the amount of time a node can go offline. You need to estimate a potential offline time and configure the archive size accordingly:
IgniteConfiguration cfg; DataStorageConfiguration storageCfg = cfg.getDataStorageConfiguration(); storageCfg.setMaxWalArchiveSize(512L * 1024 * 1024);
The default size of the WAL archive is
1Gb. Also, suppose you configure the point-in-time recovery feature. In that case,
the archive’s size becomes unlimited, and the depth of the history, which is transferred through the historical rebalancing,
is regulated by the
IGNITE_PDS_MAX_CHECKPOINT_MEMORY_HISTORY_SIZE property (set in the number of checkpoints,
100 by default).
Estimating the WAL History Size
For a more precise estimate of the required disk space, you need to consider several parameters:
How quickly the WALs are populated on a particular node
The time period a node can go offline
If the WAL compression is used
DataStorageMetrics#getWalWritingRate metric to estimate the first parameter. This metric returns the average
number of bytes written during the last minute. Note, observe this metric under a load comparable to the production one.
The second parameter, the potential offline time, should be derived from your maintenance procedures. Usually, administrators document the time of cluster repairs or maintenance restarts.
Finally, the WAL compression parameter can decrease the size of the WAL history by two times and more. The final ratio depends on your data pattern.
Overall, you can use the following formula to calculate a minimum WAL archive size for the historical rebalancing needs
wal_archive_size = wal_write_rate * node_offline_time * compression_coefficient, where the
1 if the compression is disabled, or to
[0.1-0.5] depending on your data pattern.
Refer to this calculation example for reference:
wal_write_rate = 209715200 bytes (200 Mb of WAL files per second) node_offline_time = 1800 seconds (the node can be unavailable for a half an hour) compression_coefficient = 0.5 (that is the most pessimistic prediction of compression coefficient) wal_archive_size = 209715200 * 1800 * 0.5 = 188743680000 bytes ~ 176 Gb
Configuring Historical Rebalancing Behavior
In most cases, when a node returns to the cluster, the historical rebalancing is more effective than the full one, as long as Ignite will transfer fewer data over the network. However, if the write-rate to the cluster is high, the WAL size can grow much faster than the number of records stored in partitions. In such scenarios, the full rebalancing might be more effective.
Ignite uses particular heuristics to decide which rebalancing mode to select for a given partition. Ignite falls back to the full rebalancing mode if the number of records of the partition is fewer than the number of WAL updates that need to be transferred. Otherwise, Ignite uses the historical rebalancing.
Several parameters can influence the heuristics:
IGNITE_PDS_WAL_REBALANCE_THRESHOLD- if the number of records in the partition is less than the value of this property (
500by default), Ignite will use the full rebalancing. The historical rebalancing can be fully disabled by setting a large number to this property (e.g., Integer.MAX_VALUE).
IGNITE_PREFER_WAL_REBALANCE- set this property to
trueto request Ignite to disregard the heuristics and use the historical rebalancing regardless of the number of records stored in the partition.
After a node re-joined the cluster after leaving it for some time, it’s not guaranteed that all outdated partitions will be rebalanced in the historical fashion, even if the cluster kept the full delta in WALs. It happens if another rebalancing process has changed the states of the partitions while the node was absent or some nodes haven’t stored partitions states on a disk yet.
ShutdownPolicy.GRACEFUL policy to enforce the historical rebalancing even in the conditions mentioned above:
IgniteConfiguration cfg; cfg.setShutdownPolicy(ShutdownPolicy.GRACEFUL);